RJ45 Cable Wiring of 10BaseT or 100BaseT Ethernet

RJ-45 conductor data cable contains 4 pairs of wires each consists of a solid colored wire and a strip of the same color. There are two wiring standards for RJ-45 wiring: T-568A and T-568B. Although there are 4 pairs of wires, 10BaseT/100BaseT Ethernet uses only 2 pairs: Orange and Green. The other two colors (blue andbrown) may be used for a second Ethernet line or for phone connections. The two wiring standards are used to create a cross-over cable (T-568A on one end, and T-568B on the other end), or a straight-through cable (T-568B or T-568A on both ends).

To create a straight-through cable, you'll have to use either T-568Aor T-568B on both ends of the cable. The diagram depicted on the left and right shows clip of the RJ-45 connector down.

To create a cross-over cable, you'll wire T-568A on one end and T-568B on the other end of the cable.

The straight-through cables are used when connecting Data Terminating Equipment (DTE) to Data Communications Equipment (DCE), such as cameras and computers Ethernet Switches. 

The RJ45 data cables we use to connect equipment like cameras, encoders and computers to a Ethernet switch is straight-through cables. As noted above, the RJ45 cable uses only 2-pairs of wires: Orange (pins 1 & 2) and Green (pins 3 & 6). Pins 4, 5 (Blue) and 7, 8 (Brown) are NOT used. Straight-through cable, as its name suggests, connects pin 1 to pin 1, pin 2 to pin 2, pin 3 to pin 3, and pin 6 to pin 6. Cross-over cables are used to connect TX+ to RX+, and TX- to RX-, which connects pin 1 to pin 3, pin 2 to pin 6, pin 3 to pin 1 and pin 6 to pin 2. The unused pins are generally connected straight-through in both straight-through and cross-over cables.

Pin Number Designations (10/100 Mb/s)

There are pin number designations for each color in T-568B and T-568A.

                 T-568B                         T-568A
       --------------------------      ------------------------
Pin    Color             Pin Name      Color           Pin Name
---    -------------     --------      -------------   --------
 1     Orange Stripe     Tx+           Green Stripe    Rx+
 2     Orange            Tx-           Green           Rx-
 3     Green Stripe      Rx+           Orange Stripe   Tx+
 4     Blue              Not Used      Blue            Not Used
 5     Blue Stripe       Not Used      Blue Stripe     Not Used
 6     Green             Rx-           Orange          Tx-
 7     Brown Stripe      Not Used      Brown Stripe    Not Used
 8     Brown             Not Used      Brown           Not Used


RJ-45 Wiring FAQ

1. What are T-568A and T-568B wiring standards, and how are they different?

T-568A and T-568B are the two wiring standards for RJ-45 connector data cable specified by TIA/EIA-568-A wiring standards document. The difference between the two is the position of the orange and green wire pairs. It is preferable to wire to T-568B standards if there is no pre-existing pattern used within a building.


2. What is RJ stands for?

RJ stands for Registered Jacks. These are used in telephone and data jack wiring registered with FCC. RJ-11 is a 6-position, 4-conductor jack used in telephone wiring, and RJ-45 is a 8-position, 8-conductor jack used in 10BaseT and 100BaseT ethernet wiring.

3. What is the Category Rating System?

Electronic Industries Association (EIA) developed the TIA/EIA-568-A standard, which specifies wiring and performance standards for Unshielded Twisted Pair (UTP) cabling. Category Rating System specifies the definition of performance categories for 100 ohm UTP cabling system.

Category 3 specifies the twisted pair cable and connecting hardware that can support transmission frequency up to 16MHz, and data rates up to 10Mbps. This is primarily used in telephone wiring.

Category 4 specifies cables and connectors that supports up to 20MHz and data rates up to 16Mbps. With introduction of category 5, this is a rarely used category.

Category 5 specifies cables and connectors that supports up to 100MHz and data rates up to 100Mbps. With 100BaseT Ethernet today, Category 5 is a widely used cabling system that matches todays high-speed data requirements.



CategoryTIA/EIA StandardDescription
Cat 1 None POTS, ISDN and doorbell wiring
Cat 2 None 4 Mbps token ring networks
Cat 3 TIA/EIA 568-B 10 Mbps Ethernet - frequency up to 16MHz
Cat 4 None 16 Mbps token ring networks - frequency up to 20MHz
Cat 5 None 100 Mbps Ethernet - frequency up to 100 MHz
Not suitable for GigE (1000BaseT)
Cat 5e TIA/EIA 568-B 100 Mbps & GigE Ethernet - frequency up to 100 MHz
Cat 6 TIA/EIA 568-B 2x Performance of Cat 5 & 5e - frequency up to 250 MHz
Cat 6a None Future specification for 10Gbps application
Cat 7 ISO/IEC 11801 Class F Designed for transmission at frequencies up to 600 MHz


4. What is UTP Cable?

UTP stands for Unshielded Twisted Pair. It is the cabling system with one or more pairs of twisted insulated copper wires contained in a single sheath. It is the most widely used cabling system in telecommunications and data communications environment today.








Was this article helpful?
0 out of 0 found this helpful
Have more questions? Submit a request